China excavator attachment ripper vibrate vibro ripper for 20~100 tons Excavator

Vibro Ripper, Hammer (Pile Driver)(20~100 tons Excavator

 

 

Engineering application scope 

 

*The engineering application scope* Construction site* Coal mining operation* Quarrying*Ditch work

Advantage:

 

FULL AUTOMATIC DOUBLE SAFETY SYSTEM

 

*Electronic drive system is installed in the cab,the expensive hydraulic pressure is replaced by the electric power,which saves the cost from the production. Operators in the cab can easily turn on and turn off the quick hitch through the switch.

*Check valve Protection System:each cylinder installed safety check valve ensures That quick hitch coupler can work when the oil circuit and the circuit is cut off.

*Safety Pin Protection System:security protection is customized for each excavator according to the different parameters.In the case of the failure of cylinder ,quick hitch coupler can work regularly.

 

Working principle 

Hydraulic ripper has changed the traditional working principle of reciprocating piston type. It use the destructive power produced by high speed running to make the target damage become half of liquefaction state for destruction. Its reasonable damping structure and mature hydraulic system, better protect the excavator arm and the whole hydraulic system in the construction. Due to high sealing abilityof its core parts, hydraulic ripper can easily finish underwater broken homework under the condition of not modified. At the same time relative to traditional knapper, it avoid the oil leak, black oil, replace the oil seal, liner, piston, flat pin etc. daily maintenance work and spending. In respect of loss, hydraulic ripper only need to replace the lubricating oil tank(When the lubricating oil emulsion) when necessary. While in daily work, just need to change special teeth at the tip. On special condition, common excavator teeth can also be emergency used in a short time. In the aspect of material, just need to replace 1/5 or 1/10 parts of the traditional knapper drill rod, more comply with the concept of green environmental protection.

 

*The core part of this equipment is completely closed and is driven by high speed anti-knock

motor. Hydraulic oil just go through motor while not core box, so that metal grinding loss of dirt may not go to the excavator body, so will not be black oil and oil leak.

* Hydraulic ripper work characteristics is single point contact drive around, that is to say when make a point of the surrounding soil or ore also being destroyed. This is the reason of having the effect of secondary crushing  and high efficiency.

* Hydraulic ripper has low loss. Due to the design of the oil is only input and one output, itself nearly has no loss of hydraulic oil, also on the stock just tip of bucket teeth.

* The structure of hydraulic ripper is reasonable, there are damping rubber at the top and sides. In this regard has reduced 80% vibratory force, so under the condition of damping rubber is normal there is nearly no damage on excavator.

* The biggest advantage of hydraulic ripper is repair and maintenance. In addition to regularly changing lubricating oil of core box, it basicly don't need maintenance. Wear parts enclose gear, rubber, bucket tooth, bearing and wear parts replacemen frequency is only 20%-25% of the ordinary knapper.

Performance Parameter

		Model BY-HR250	Model BY-HR350
Hydraulic excavator	tons	20-25	24 - 30
Mass of ripper (incl. top bracket)	kg	2350	3500
Mass of ripper (less top bracket)	kg	2800	2800
Hydraulic working pressure	MPa	22 - 24	22 - 24
Hydraulic return pressure	MPa	0.6	0.6
Hydraulic oil flow	L/min	180	180
Case drain max. pressure	MPa	0.4	0.4
Frequency	L/min	1300	1300
Dimensions L x W x H	mm	2300x1030x1100	2650x990x1500
Accumulator pressure	Mpa	0.5	0.5

 

Construction picture

 

Please click products below to see more details

 

 

 

 

Yes, we are a factory,more then 10 years factory

 

2,Where are your factory ?

Address: A park, ShuangMiao Industrial, HuiShan District, Wuxi, Jiangsu, China ,You can by train form shanghai to Wuxi station ,then we will drive the car to pick you up!

 

3, What is your delivery time?

 Within one week.

 

4, What's your payment ?

30% deposit against the contract by T/T should be paid before the order;

70% balance should be paid off by T/T after inspection before delivery;