Overview
| New and old degree | brand new | specifications | Thickened steel plate |
| principle | Hammer type | Processing customization | yes |
| voltage | 380V | Applicable objects | Straw, rice straw, peanut seedlings, etc |
| power | 7.5kw | Applicable scope | Breeding feed processing |
| application area | Agriculture and animal husbandry | Crushing fineness | 0.6mm-4.5cm |
| Automation level | Semi automatic/fully automatic | after-sale service | One year warranty |
| model | Shakelon dust removal crusher | brand | Taifeng Machinery |
Product Details
Hammer type feed crusher
The feed crusher is mainly used to crush all types of feeds and rough pages The purpose of feed crashing is to increase the feed surface area and adjust the particle size, increase the surface area and improve the feasibility It is easy to contact with the digest juice in the digest edge, which is conductive to improving the digest and better absorbing the feed nutrients On the one hand, the adjustment of particle size reduces the energy consumption of animal cooking, on the other hand, it is more conservative for transportation, storage, mixing and granulation, with better efficiency and quality
Paddle mill
Instructions for use
The crusher shall be fixed on the cement foundation for long term operation If the working place is frequently changed, the grinder and motor shall be installed on the base made of angle iron If the grinder is powered by diesel, the power of the two shall be matched, that is, the power of the diesel engine is slightly greater than that of the grinder, and the pull grooves of the two shall be consistent, and the outer end face of the pull shall be on the same plane
2. After the installation of the crusher, check the fastening of the fasteners of each part, and tighten them if they are loose
3. Check whether the belt tightness is appropriate and whether the motor shaft and the crusher shaft are parallel
4. Before starting the crusher, turn the rotor by hand to check which of the other class, hammer and rotor operate flexibly and reasonably, where there is consolidation in the shell, where the rotation direction of the rotor is consistent with the direction indicated by the arrow on the machine, and where the motor and the crusher are well integrated
5. Do not replace the belt Pulley Casually to prevent the crushing chamber from exploring due to too high rotating speed, or the working efficiency is affected due to too low rotating speed
6. After the pulverising table is started, it shall be idle for 2-3 minutes, and then it shall be put into operation after there is no abnormal phenomenon
7. Pay attention to the operation of the crusher at any time during work The feeding shall be uniform to prevent blocking and blocking the vehicle Do not overload the operation for a long time In case of vibration, noise, high temperature of bearing and machine body, outward spraying, etc., stop the machine immediately for inspection, and continue to work after troubleshooting
8. The crushed materials shall be carefully inspected to avoid accidents caused by hard objects such as copper, iron, and stones entering the crushing room
9. The operator shall not wear glasses, and shall stand at the side of the crusher during feeding to prevent the bounce debris from hurting the face
Maintenance
1. Timely check and clean up After the work every day, the machine shall be cleaned in time, and the scratches at each part shall be checked for noise and the wear of vulnerable parts such as tooth classes and sieves
2. Fill with grease The most common method is to assemble a cap type oil cup on the bearing Generally, rotate the oil cup cover for 1/4 turn every 2 hours and press the degree in the cup into the bearing In the case of sealed bears, degree can be added every 300 hours After long term use, if the degree criteria, the bearing should be cleaned and replaced with new degree When the machine is working, the temperature rise of the bearing should not exceed 40 ℃ If the bearing temperature continues to rise under normal working conditions, find out the cause and try to terminate the fault
3. Carefully clean the raw materials to be crushed It is strictly forbidden to mix copper, iron, lead and other metal parts and large stones into the crushing room
4. Do not arbitrarily increase the speed of the crusher Generally, the allowable difference from the rated speed is 8% -10% When the crush works together with a larger power machine, pay attention to control the flow and make the flow uniform, not fast or slow
5. After the machine is started, do not disassemble or inspect any part of the machine Various tools should not be placed on the machine randomly When abnormal sound is heard, stop the machine immediately, and conduct maintenance after the machine stops stably
Common faults
Common fault I: weak operation, startup, power on, etc
Maintenance scheme: in this case, it can be repaired by itself First, check where the power socket, plug and power line has oxygen shelding and frame If not, plug in the power supply for test When the motor is powered on and does not rotate, and the wheel can rotate against generously pulling the wheel by hand, it can be included that one of the two starting capacitors of the machine is caused by capacity
TF series hammer feed grinder
Total weight: kg
Boundary dimension: mm
Equipped power: kw
Spindle speed: r/min
Number of hammer pieces: pieces
Sieve diameter: 0.8-12mm
Yield (KG/H)
Power (KW)
Number of hammer pieces (pieces)
Crushing chamber
(mm)
Spindle operation
(rpm)
TF-280
100-120
2.2 Lighting electricity
twelve
two hundred and eighty
three thousand and six hundred
TF-340
200-300
3 Lighting electricity
twelve
three hundred and forty
three thousand and six hundred
TF-400
400-500
seven point five
sixteen
four hundred
three thousand and five hundred
TF-420
600-800
eleven
sixteen
four hundred and twenty
three thousand and five hundred
TF-500
1000-1500
fifteen
twenty-four
five hundred
three thousand and four hundred
TF-50-30
2000-3000
eighteen
twenty-four
five hundred and thirty
two thousand and eight hundred
TF-50-40
4000-5000
twenty-two
twenty-four
six hundred
two thousand and eight hundred
TF-50-50
6000-7000
thirty
thirty
seven hundred
two thousand and eight hundred
TF series large hammer feed crusher
Total weight: kg
Boundary dimension: mm
Equipped power: kw
Spindle speed: r/min
Number of hammer pieces: pieces
Sieve diameter: 0.8-12mm
Yield (KG/H)
Power (KW)
Number of hammer pieces (pieces)
Crushing chamber
(mm)
Spindle operation
(rpm)
Price (including dust removal)
TF-460
600-800
fifteen
twenty-four
three hundred
three thousand and five hundred
TF-50-40
2000-3000
twenty-two
twenty-four
four hundred and thirty
three thousand and three hundred
TF-50-50
3000-4000
thirty
thirty
five hundred and thirty
three thousand and three hundred
TF-50-60
4000-5000
thirty-seven
thirty-six
six hundred
three thousand and three hundred
TF-50-80
5000-5500
fifty-five
forty-eight
eight hundred
three thousand and three hundred
TF-50-100
5000-6000
seventy-five
sixty-four
one thousand
three thousand and three hundred
Hammer crusher has two types: dust removal and non dust removal, and customers can choose according to their own production